Microsoft Word XXXXXXXXXXSP6 UO Structures 1 Test Master.docxMELNY003‐1 Naphtali Meltzer ...

1 answer below »
see file for instructions


Microsoft Word - 2022 SP6 UO Structures 1 Test Master.docx MELNY003‐1 Naphtali Meltzer  Page 1  ASSESSMENT DESCRIPTION  In this test, apply the relevant concepts covered in this course. In the first question, design different members of a  truss, and in the second question determine loads, bending moments, shear forces and deflections in a building  structure. Where relevant, reference the relevant Australian Standard Loading Codes AS1170 and ASI Design  Capacity Tables for Structural Steel. Resources from weeks 1 ‐ 10 will be a valuable reference.  Notes:  1. Test Conditions apply and there is to be no discussion with anyone else and no questions asked of teaching staff for the duration of the test.  Late submissions will not be accepted. 2. The Grade and Feedback for Assessment 1 Part B will be returned after both the Test (Assessment 2) has been submitted and the Test deadline has elapsed. o All Calculations must be typed, preferably using the Word Equation Editor. Handwritten calculations will not be assessed. 2022 SP6 UO Structures 1 – Assessment 2  MELNY003‐1 Naphtali Meltzer      Page 2  UO Structures 1 Test Instructions  Read this page in detail   The Test is out of 100 marks and is worth 35% of overall course grade     Answer All Questions     All Calculations must be typed, preferably using the Word Equation Editor. Handwritten calculations will not  be assessed.                    * Preferably, type the calculations using equation editor in MS Word.                     *Excel spreadsheets and software analysis tools will not be accepted for Meltzersubmission     Word document submission only  o Excel spreadsheets and software analysis tools will not be accepted for submission     Where relevant, diagrams must be included with calculations (e.g. Free body diagrams, tributary areas)  and these can be hand drawn and scanned in.  o Clear and informative diagrams can help the assessor follow your calculations and reasoning.     For full marks for any part of a question, working must be displayed and units must be correct at every step  of working.  o For example, in Question 1 Part A the correct support reactions with no working or free body  diagram(s) to show how the support reactions were obtained, will only score 1 out of 10 for that  part.     The marks for each part are underlined in bold font     Answers are to be correct to 2 decimal place.  o For example, an answer of “The force in member YZ is 125.367 kN (Compression)” can be written as  The force in member YZ is 125.37 kN (Compression)  o For example, an answer of “The force in member YZ is 300.00 kN (Compression)” can be written as  The force in member YZ is 300 kN (Compression)     The Design Properties and Capacity Tables can be found in the Assessment 2 Section on the Course website.     You will need to access the Australian Standards, especially AS/NZS 1170.1:2002 via Techstreet at the UniSA  Library.        2022 SP6 UO Structures 1 – Assessment 2  MELNY003‐1 Naphtali Meltzer      Page 3  QUESTION 1  Use Figure 1, a pin jointed steel truss with bolted connections and the values presented in Tables 1 and 2, as well as  your mathematical thinking and reasoning to respond to the following questions.  a) Ignoring the self‐weight of the members, determine the support reactions.    10 marks    b) Ignoring the self‐weight of the members, determine the force in the four members AB, AD, CD and AC.                         15 marks    c) Design members AB, AC and BC.  Use Equal Angle (EA) Sections for members in Tension and assume the  member is bolted with 1 Hole in Leg.  Use Square Hollow Sections (SHS) for members in Compression.  For  zero‐force members use SHS 65x65x1.6.            12 marks    d) Determine the stress, strain and elongation/shortening of member AB (Assume Esteel = 200,000 MPa)                        8 marks    e) Design the bolts for the connections on members AB, AC and BC. Use the same “Grade:8.8” bolt size for all  connections.  That is, whatever bolt size is selected on one member, needs to be used on the other three  members.                    9 marks    f) The steel price is $14 per kg, and the bolt price is provided in Table 2. Determine the total cost of the  material to build members AB, AC and BC.            6 marks    Remember to include free body diagrams at part (a) and part (b) and your answers must be consistent with the  orientation of the truss presented in Figure 1.    2022 SP6 UO Structures 1 – Assessment 2  MELNY003‐1 Naphtali Meltzer  Page 4  Table 1: Parameters for Question 1  P1  P2  P3  ?  ?  L1  L2  L3  150kN  220kN  270kN  40° 55°  4.2m   2.9m   4m  Figure 1: Steel Truss with bolted connection  Remember to include free body diagrams at part (a) and part (b) and your answers must  be consistent with the orientation of the truss presented in Figure 1.  The x‐axis is the horizontal axis.  The y‐axis is the vertical axis.  2022 SP6 UO Structures 1 – Assessment 2  MELNY003‐1 Naphtali Meltzer      Page 5  Table 2: Cost per bolt  Cost per Bolt  Bolt  Size  Grade:  4.6  Grade:  8.8  M12  $9    M16  $11  $20  M20  $15  $24  M24  $17  $26  M30  $21  $28  M36  $23          2022 SP6 UO Structures 1 – Assessment 2  MELNY003‐1 Naphtali Meltzer      Page 6  QUESTION 2  A simple 6 storey building is to be constructed in Adelaide.  Use the details provided in Figure 2, Figure 3, and Table 3 to respond to the following questions.  a. Calculate the dead load and live load per area of the floor.  The floor dead load consists of the floor  weight plus a superimposed dead load for the wall partitions.        7 marks    b. In the second floor beams, determine the maximum moment and maximum shear for beams A4‐B4 and  B4‐C4 due to live load only.  Also, in no more than 50 words, compare and discuss the maximum  moment and shear of the two beams.              10 marks    c. Calculate the deflection of beams A4‐B4 and B4‐C4 in the Second floor due to the dead load only if a  cross section of 250 UB 37.3 is used.  Also, in no more than 50 words, compare and discuss the  deflection of the two beams.                    6 marks    d. In no more than 100 words, explain why I‐shaped sections are usually used for beam members and also  explain which part of an I‐shaped section resists shear and which part resists moment.                            5 marks  e. Column   i. Determine the force in columns A2 and B2 at the First Floor and Second Floor, due to dead load  only                      6 marks  ii. In no more than 50 words, Compare and discuss the loads of the edge (A2) and internal (B2)  column.  Also, in no more than 50 words, compare and discuss the loads of these columns in the  Second and First floor.                6 marks    Your calculations are to be based on the following design assumptions:   Ignore the weight of the beams and columns.   Beams are simply supported at their ends   The building has N levels  o First Floor  o Second Floor  o …  o Nth Floor   The loads on all floors including the roof (which is the ceiling of the Nth Floor) are the same   The slab design is a One‐way slab in the Y‐axis direction   Assume Esteel = 200,000 MPa   If required, make further design assumptions and justify with suitable explanations.      2022 SP6 UO Structures 1 – Assessment 2  MELNY003‐1 Naphtali Meltzer      Page 7    Table 3: Parameters you will use for Question 2  Number of  floors (N)  Building  function  Dead load due to   partitions (kPa)  L1  (m)  L2  (m)  L3  (m)  L4  (m)  L5  (m)  Storey  height (m)    6  Dance Studio  1.8kPa  4.5m  3.7m  5.1m  3.6m  3.5m  4m    Floor Details (See Figure 2)    Floor surface  Sand  Concrete Slab  Ceiling    Cinder‐concrete filling  Sand  Reinforcement ratio= 2.5%  Lime plaster  Thickness  11mm  35mm  240mm  29mm        Ceiling Floor surface Sand Concrete Figure 2: Floor Detailing         2022 SP6 UO Structures 1 – Assessment 2  MELNY003‐1 Naphtali Meltzer      Page 8    A B C 1 2 3 4  L 3        L 4      L 5      L2     L1    Y X Figure 3: Typical Floor Layout Plan
Answered 1 days AfterNov 23, 2022

Answer To: Microsoft Word XXXXXXXXXXSP6 UO Structures 1 Test Master.docxMELNY003‐1 Naphtali Meltzer ...

Banasree answered on Nov 24 2022
36 Votes
1.a
Tanα= 2.9/4.2=0.69
Α=36.60
=0
P1cosꟗ = Dx +P2cosθ
Dx = P2Cosθ-P1cosꟗ
    = 82.493KN(T/C)
=
0
Ay+Dy+P1sinꟗ = P2sinθ+p3
Ay+Dy = 288.540KN(T/C) ……………………..1
=0
=0
Ay*(L+L2) +P3*L2 = P2Sinθ*L3 +P1 Cosꟗ*L2
Ay = 4.529KN(T)………………..2)
Equating 1 and 2
Dy = -293.069KN(C)
b)
Joint at A
...
SOLUTION.PDF

Answer To This Question Is Available To Download

Related Questions & Answers

More Questions »

Submit New Assignment

Copy and Paste Your Assignment Here