need techinal report based on file Base Data V5.0
associate degree in electrical engineering ASSOCIATE DEGREE IN ELECTRICAL ENGINEERING TAFE-SA ASSOCIATE DEGREE IN ELECTRICAL ENGINEERING Task-3 (Marking Guide) (Total – 28 marks) 1) Format of the report – 2 marks 2) Summary – 1 mark 3) Forms/ applications for approval from various stakeholders/ authorities – 1 mark 4) Project overview – 1 mark 5) Scope – 1 mark 6) Exclusions/ constraints – 1 mark 7) Assumptions – 1 mark 8) Cost – 1 mark 9) Payment schedule – 1 mark 10) Diary planning (schedule) – 1 mark 11) Risk management (Delays, variations, negotiation, conflict resolution clauses) – 4 marks 12) Warranty (validity) – 1 mark 13) Document control – 1 mark 14) Deliverable to the customer – 1 mark 15) Procurement plan – 1 mark 16) Roles/ responsibilities – 1 mark 17) Budget – 1 mark 18) Ethical considerations – 1 mark 19) Checklist for audit – 1 mark 20) Contract – 1 mark 21) Quote – 1 mark 22) Closure – 1 mark 23) Appendices – 1 mark 24) References – 1 mark Regency Institute of TAFE Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 1 of 13 Electrical Engineering Program Tonsley Campus Design Project INSTRUCTIONS TO STUDENTS 1. Access the Moodle site for a comprehensive break down of requirements. 2. Team work is encouraged, but assessment will be on an individual basis. 2. If a question involves calculations, all working out should be shown. 3. All references used shall be included as part of the project and must be referred to for all instances your selection/decision requires their use. Associate Degree in Electrical Engineering Capstone Project Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 2 of 38 PROJECT OUTLINE TAFESA Electrical Engineering Department have been contracted to install all of the electrical cabling and equipment for three industrial units consisting of office space, factory floor space, storage shed, car-parking and load/unloading facilities. The new installation will be located at Lot 101 Brodie Road Lonsdale, South Australia 5160. You must provide an Information Pack to TAFESA Electrical Engineering Department to support your planned electrical distribution system that complies with latest edition of AS/NZS3000, AS/NZS3008.1.1 and the South Australian Power Networks’ Service and Installation Rules All details for the Consumer Mains, Sub-mains, FSCs, all circuit protection details and interrupting capacities must be included. Goode Construction has provided the following information with respect to this Project: • Installation Details • Electrical Details • Installation Site Plan • Individual Unit Site Plan • Individual Unit Floor Plan • Some Electrical Appliance Data Sheets NOTE: The information provided in this Project Guide is just that, a GUIDE! You will be required to provide all documentation needed to support your conclusions i.e. every cable selected shall have a supporting cable selection calculation! Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 3 of 13 Installation Site Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 4 of 13 Installation Details: • The dwelling will be fed via an underground service from a pad mounted transformer as per the Installation Site Plan. The transformer is 750kVA 3%Z located 10m from the Main Switchboard. • The Consumer’s Main shall be protected by Supply Authority’s service fuses and the required panel/meter isolators. The Sub-mains shall be protected by circuit breakers. The underground services are to be installed as detailed on the Installation Site Plan. • The Sub-mains are to be installed as per the provided Site Plan. Note that due to the size of this installation, each shed will be considered as an out-building with regards to the Earthing arrangements, allowing separate MEN installations. • The Units will be a combination of construction methods. The factory walls will be predominantly concrete and the roof is a steel framework with cliplock sheeting. The offices internal walls will be utilising plasterboard and a wooden frame. Insulation is installed in the walls and ceiling of the office area only. The anticipated ambient temperature in the office is 30°C and 40°C in the factory. • V90, PVC/PVC, TPS cables shall be used for all FSCs within the dwelling. • Circuit protection shall be circuit breakers or circuit breaker/RCD combinations. • All electrical components, where possible, are to be Clipsal, NHP or Schneider brand. Sub-Contracting • Any third party providing work is to be covered in this documentation Application Forms All application forms to be completed and submitted with quote • Underground Electrical Connection Application form available from the council website • Supply Authority/retail • Retailer by negotiation Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 5 of 13 Electrical Details Each unit will have the Consumer Mains, Sub-mains, Main Switch-Board(s) and all Distribution Boards determined/planned for the recommended following loads. Office 40 x LED Ceiling Lights (Allow 28W per fitting) 20 x LED Down-lights for Office Reception (Allow 11W per point) 6 x Exit/Emergency Lights 10 x Emergency Lights 8 x Exhaust fans 30 x Double 10A, 230V Socket Outlets 4 x Single 10A, 230V Socket Outlets 2 x Ranges (Refer to data sheet last page) 1 x 3Ø, Ducted Air Conditioner for Offices only (Refer to data sheet last page) Factory 24 x H5 series LED High-bay Fittings 200W (HB5200) 4 x Floodlight LED (150W) (SL5150) 3 x Exit/Emergency Lights 6 x Emergency Lights 2 x HVLS Industrial Ceiling Fans (Revolution 2HP Fans - Refer to data sheet) 12 x Double 10A, 230V IP56 Industrial Socket Outlets 6 x Single 10A, 230V IP56 Industrial Socket Outlets 2 x 10A, 400V IP56 Industrial Socket Outlets 4 x 15A, 400V IP56 Industrial Socket Outlets 2 x 20A, 400V IP56 Industrial Socket Outlets 2 x 32A, 400V IP56 Industrial Socket Outlets Shed 8 x LED Ceiling Lights (Allow 28W per fitting) 8 x Double 10A, 230V Socket Outlets 2 x Single 10A, 230V Socket Outlets 4 x Floodlight LED (150W) (SL5150) Communal Load: 3 x Car parking lights - Allow 200W per fitting 5 x Truck/Deliveries Access lane lights fitted along external wall of Unit 3 -Allow 150W per fitting 4 x Single 10A, 230V Socket Outlets located in service boards. Street-side signage – Allow 500W Automated Gate Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 6 of 13 Basic Security for all entrances Sensor at entrance ways Input panel Programmable unit Office doors on timer and sensor Rear roller doors on sensor with notifications to panel Motor drive unit for the automated gate Able to drive 1 metric ton gate on track Feedback for; Fully open Fully closed Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 7 of 13 Installation Site Map for Electrical Distribution System Show location of Main Switchboard, POS, underground cable routes, communal services and other service provisions (such as FIP, Security etc.) . Car Park Size 30m (L) x 12m (W) allowing 20 car spaces Office Ground Floor - 12m x 6m office space with a 3m x 3m Disable toilet area provided. First Floor - 12m x 10m (Void of 6m x 4m above Reception area). Factory Floor Size 12m (W) x 90m (L) x 6m (H) Truck awning provided at rear being 12m (W) x 5m (L). Shed Gable roof Size 12m x 12m x 3m Brodie Road Car Park Office Office Office U ni t 3 – F ac to ry F lo or U ni t 2 - F ac to ry F lo or U ni t 1 – F ac to ry F lo or U3 Shed U2 Shed U1 Shed Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 8 of 13 Individual Unit Site Plans - Highlighting the interconnection between all sub-sections • Office and Factory Ground Floor – Layout below • Office First Floor - Layout below • Shed – 12m x 12m Stratco® Gable roof shed. Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 9 of 13 Bosch Appliance details Mitsubishi Air Cond Cat No Item Quantity $/item Total Price Wall Oven Energy input Electric Electrical connection rating (W) 5,500 W Current (A) 20 A Voltage (V) 240 V Frequency (Hz) 50 Hz Electrical Supply - Single Phase 240 volt /Single Phase / 50 Hertz - Three Phase* 415 volt / Three Phase / 50 Hertz Breaker Size - Single Phase A 32 Three Phase* A 16 Heating Capacity (Rated Conditions) kW 11.2 Cooling Capacity (Rated Conditions) kW 10 http://media.bosch-home.com/Files/Bosch/Au/au_en/ProductFiles/ProductImages/EpsImages/MCSA038393_HBM43B550A_def.eps?Width=550 Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 10 of 13 Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 11 of 13 Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 12 of 13 SPECIFICATIONS Emergency Lighting Associate Degree in Electrical Engineering Capstone Project 2019 V 5.0 13 of 13