Table 3.3b Toerances for shafts of sizes up to 100 mm (from j to s) Diameter steps in in 6. 5-6 6 7. 6-7 7 6-7 6-7 5. 6 5-6 6. 7 5-7 over to es ei es ei es ei es ei es es ei ei es ei es ei 3. +2 -2 +4...

Determine the limits of sizes, tolerances and fundamental deviations for the shaft designated as 40 H8 / f7

use fundemental deviation for shaft f7, es=-5.5(D)^0.41

Extracted text: Table 3.3b Toerances for shafts of sizes up to 100 mm (from j to s) Diameter steps in in 6. 5-6 6 7. 6-7 7 6-7 6-7 5. 6 5-6 6. 7 5-7 over to es ei es ei es ei es ei es es ei ei es ei es ei 3. +2 -2 +4 -2 +6 -4 +4 +6 +8 +2 +10 +14 +4 +12 +16 +6 +14 +16 +10 +18 +20 +24 +14 3 +3 -2 +6 -2 8+ 4 +6 +9 +1 +12 +16 +4 +16 +20 +8 +20 +24 +12 +20 +23 +15 +24 +27 +31 +19 10 +4 -2 +7 -2 +10 -5 +7 +10 | +1 +15 +21 +6 +19 +25 +10 +24 +30 +15 +25 +28 +19| +29 +32 +38 +23 10 18 +5 -3 +8 -3 +12 +9 +12 +1 +18 +25 +7 +23 +30 +12 +29 +36 +18 +31 +34 +23 +36 +39 +46 +28 18 30 +5 -4 +9 -4 +13 +11 +15 +2 +21 +29 +8 +28 +36 +15 |+35 +43 +22 |+37 +41 +28 +44 +48 +56 +35 30 50 +6-5 +11 +15 -10 | +13 +18 +2 +25+34 +9 +33 +42 +17 |+42 +51 +26 +45 +50 +34 +54 +59 +68 +43 50 80 +6 -7+12 -7 +18 -12 +15 +21 +2 +30 +41 +11 +39 +50 +20 |+51 +62 +32 +55 +61 +42 | +69 +75 +86 +56 80 100 +6 -9 +13 -9 +20 -15 +18 +25 +3 +35 +48 +13 +45 +58 +23 +59 +72 +37 +66 +73 +54 +86 +93 +106 +71 51


Extracted text: Table 3.2 Tolerances for holes of sizes up to 100 mm (H5 to H11) Diameter H steps in mm 5 6. 7 10 11 5-11 over to es ei 3 +4 +6 +10 +14 +25 +40 +60 0. +5 +8 +12 +18 +30 +48 +75 6. 10 +6 +9 +15 +22 +36 +58 +90 0. 10 18 +8 +11 +18 +27 +43 +70 +110 18 30 +9 +13 +21 +33 +52 +84 +130 30 50 +11 +16 +25 +39 +62 +100 +160 50 80 +13 +19 +30 +46 +74 +120 +190 0. 80 100 +15 +22 +35 +54 +87 +140 +220